電工鋼硅鋼片供方可采用不同的檢驗和試驗方法進行驗收測試，發生爭議時，應采用本文件規定的檢驗和試驗方法及相關的技術要求進行測試。9 判定與復驗規則產品的判定與復驗規則應符合 GB/T 17505 的規定。規定的磁性能及工藝性能檢驗項目中，如有某一項試驗結果不符合本文件要求，則從同一批中再任取雙倍數量的試樣進行該不合格項目的復驗。復驗結果(包括該項目試驗所要求的所有指標)合格，則整批合格。復驗結果(包括該項目試驗所要求的所有指標)即使有一個指標不合格，則復驗不合格。如復驗不合格，則已做試驗且試驗結果不合的單件不能驗收，但該批材料中未做試驗的單件可逐件重新提交試驗和驗收。

電工鋼硅鋼片1882~1995年主要是熱軋硅鋼的發展階段。1903年美國和德國首先開始生產熱軋硅鋼。1905年美國（英國在1906年）已經大規模生產，在很短的時間內全部替代了普通低碳鋼板制造電機和變壓器。由于冷軋無取向硅鋼的磁感、吉林遼源當?shù)罔F損、吉林遼源當?shù)貨_剪加工性、吉林遼源當?shù)乇砻尜|(zhì)量和絕緣涂層等質量性能都大大優于熱軋硅鋼，并且熱軋產品不能成卷生產，降低了沖片效率，60年代主要的工業發達 都陸續停止生產熱軋硅鋼。1957年，前西德阿什姆斯在實驗室內生產出了雙取向硅鋼片（立方織構的硅鋼）。沿軋向和橫向都有很高的磁性，但尚在實驗室階段，未投入工業生產。

電工鋼硅鋼片In addition to the types listed above, there are also some special purpose electrical steel plates, such as 0.15 and 0.20mm thick 3％ Si cold-rolled non oriented silicon steel strips and 0.025, 0.05, and 0.1mm thick 3％ Si cold-rolled oriented silicon steel strips, used for medium and high-frequency motors, transformers, and pulse transformers； 0.7mm thick 3％ Si high-strength cold-rolled non oriented silicon steel plate for relays and power switches； High strength cold-rolled electrical steel plate for new high-speed motor rotors； Low carbon electrical steel hot-rolled thick and cold-rolled plates for magnetic shielding and high-energy accelerator electromagnets such as medical magnetic resonance tomography scanners； 4.5％ to 6.5％ Si high silicon steel plates for high-frequency motors, transformers, and magnetic shielding.Generally, motors, transformers, and other electrical components are required to have high efficiency, low power consumption, small size, and light weight. Electrical steel plates are usually guaranteed to have magnetic properties based on core loss and magnetic induction strength [1] [2]. The requirements for the performance of electrical steel plates are as follows:Low core loss (PT)Iron core loss refers to the ineffective electrical energy consumed by an iron core when magnetized in an alternating magnetic field of ≥ 50Hz, abbreviated as iron loss, also known as alternating loss, and its unit is W/kg. The ineffective electrical energy consumed due to various obstacles caused by magnetic flux changes not only loses electrical energy through the heating of the iron core, but also causes temperature rise of the motor and transformer. The iron loss (PT) of electrical steel includes three parts: hysteresis loss, eddy current loss (Pe), and anomalous loss (Pa). Electrical steel plates have low iron loss, which can save a lot of electricity, prolong the operating time of motors and transformers, and simplify cooling devices. Due to the iron loss of electrical steel plates, which accounts for 2.5％ to 4.5％ of the annual electricity generation in various countries, countries always try their best to reduce iron loss in the production of electrical steel plates, and use iron loss as the most important indicator to assess the magnetic properties of products. The iron loss value of products is used as the basis for classifying product grades. Cold rolled oriented electrical steel: Cold rolled oriented electrical steel is a high-end product in the field of electrical steel. Compared with cold rolled non oriented electrical steel, its magnetism has strong directionality； It has superior high magnetic permeability and low loss characteristics in the direction of easy magnetization rolling. The iron loss of oriented steel strip in the rolling direction is only 1/3 of that in the transverse direction, and the ratio of magnetic permeability is 6:1. Application: The main purpose of cold-rolled oriented silicon steel strip is for transformer manufacturing.Full process cold rolled non oriented silicon steel coating: The surface of the full process cold rolled silicon steel is coated with a semi transparent insulation coating, which has different codes in different standards. Taking Baosteel‘s Q/BQB 480 2014 as an example: